910 W Anderson, Waurika, Oklahoma

A 1908 house getting its siding, trim and cottage look back

A sage-and-white cottage exterior over restored wood siding, rebuilt window trim and porch, one shallow well on the lot to irrigate both houses, and board and batten inside.

Exterior
Sage, white trim
Built
1908
Walls
Clapboard on studs
Parcels
910, lot, 922
Interior
Board and batten
Well
40–50 ft, about $5,000
Goal: sage green cottage with white trim, porch and planted beds
The goal. Sage siding, white trim, square porch columns, beds held off the house.

Property overview

The 1908 yellow house at 910 W Anderson is getting a proper wood-siding restoration and a cottage makeover; a shared irrigation well will serve it and 922 W Anderson.

Item Detail
Parcels 910 W Anderson (1908 yellow house), empty lot, 922 W Anderson; all owned
Walls Painted wood clapboard nailed straight to studs; no sheathing or housewrap
Insulation Blown in through drilled holes; raised plugs remain in the siding
Foundation Cement; soil has been pulled back from the wall
Moisture Dry climate; wood was dry when the vinyl came off
Termites Old damage found; looks inactive and possibly treated before
Vinyl removal damage Hundreds of nail holes, split butt joints, hacked window caps, water table chopped at the base

Siding and base

The goal is sound and sealed, not smooth: keep the laps open, seal every hole in the board faces, and keep wood well clear of the soil.

Rules

  • Never caulk the horizontal laps. They are the only drainage and drying path. Cut out the continuous caulk bead already run under the boards.
  • Caulk the vertical butt joints, the trim, the casings and the corner boards.
  • Scrape loose paint back to tight edges. Remove grey weathered wood. Wash, dry, and spot-prime bare wood within about two weeks.
  • Lead paint is assumed: wet-scrape, keep plastic under the work, and sand only with HEPA dust extraction.

Fillers by size

What Filler
Small nail holes, up to ⅛" Exterior-rated filler or paintable urethane-acrylic caulk
Holes ¼" and up, gouges Two-part epoxy (WoodEpox type); Bondo only for small holes in stable wood
Stable splits and checks over 1/16" Epoxy, with consolidant first if the wood is soft
Cracks that move with the weather Paintable urethane-acrylic caulk
Insulation plugs Replace with wood plugs set flush in epoxy

Water table (rebuild at the base)

  • Remove the hacked remnant entirely. Probe the sill and borate-treat it (Bora-Care or Timbor) while it's open.
  • Put peel-and-stick or felt on the sill face, tucked up behind the lowest clapboard course.
  • 5/4 cedar face board with a PVC cap sloped 15° or more. Drip kerf ⅜" in from the front edge, ¼" deep. Back-prime all six faces.
  • Z-flashing from behind the siding, lapping over the cap.
  • Lap the board down about 1" past the joint where the sill meets the concrete. Leave the bottom edge uncaulked.
  • Nail into the studs and sill with stainless or hot-dip galvanized nails.

Grade and termites

  • Keep at least 6" between soil and wood. Slope the soil away about 6" over the first 10 ft. Keep the brick edging, pavers and mulch from building back up against the wall.
  • Check the exposed foundation for mud tubes. To test whether termites are still active, break a tube and look again in a week.
  • Consider a termite inspection or preventive bait system; any old treatment has likely worn off.

Other work on this wall

  • Porch deck boards: leave a gap of about ½" from the siding.
  • Gas meter: notch the water table around the riser and keep paint off the regulator vent.
  • Old window opening: flash behind the lined-up butt joints; add a felt or housewrap panel behind the patch if the boards come off easily.

Windows, trim and porch

Keep the original double-hung sash-cord windows and rebuild the trim to one consistent pattern: head casing plus a separate cap.

Casings

  • Original casings were removed for repair. Reuse them where sound: flip the protected back face out, or plane lightly after stripping paint and pulling every nail.
  • Replace badly weathered pieces with clear cedar planed to the original thickness (often a true ⅞").
  • Don't remove casings from windows that aren't being worked on. They're part of the frame and hold the blind stop.
  • Leave the weight pockets open, with no insulation. Tape the outer joints only.

Head cap (every window)

  • 5/4 clear cedar, top bevelled about 10°, about 1" overhang on the front and ends.
  • Drip kerf on the underside; add a bed moulding if the originals had one.
  • Metal flashing over the cap, tucked up behind the siding course above.
  • Whole head (casing plus cap) about 1¼–1½× the side casing width.
  • Double window under the porch: remove the newer filler board above the head casing, then add a proper cap.

Sash and sills

  • Re-cord with waxed cotton sash cord (#7 or #8), reglaze, and add spring-bronze weatherstripping.
  • Consolidate and epoxy sound sills; make new ones from white oak, sapele or cedar where rotted.

Joinery and wood

  • Festool Domino with Sipo tenons, glued with Titebond III or epoxy.
  • Build casing and head assemblies on the bench and prime all six faces before installing.
  • Clear cedar is roughly $6–12 per board foot, versus $1–2 for #2 pine. That's about $30–60 more per window, and worth it.

Porch

Front porch before: thin post, iron column on a brick pier, vinyl-wrapped beam
Before. Thin post, iron column on a brick pier, vinyl-wrapped beam.
Front porch goal: sage siding, white trim, chunky square white columns and a solid beam
After (goal rendering). Square white columns, a solid white beam, sage siding. The rendering shows the look, not exact sizes.
  • Beam: 1×10 or 1×12 face board plus a soffit board underneath, returned ends, and drip or flashing on top. Check the header underneath first.
  • Columns: wrap the thin post to 7¼–8" square with a base and cap trim, held ½" off the floor. Make the right column match.
  • Brick pier: remove it (shore the beam first). Set the new column on a footing with a standoff base.

Possible new window

  • Restore the original opening on the long wall (the patched vertical seam).
  • Head in line with the other windows. Check or rebuild the header, since it's a bearing wall.
  • Check gas meter vent clearance (usually about 3 ft from windows that open) and ask the city about a permit.

Paint, cottage look and tools

The look is sage green siding with white trim and a dark door. One protective coat goes on now in the final colour, then a second coat after the repairs.

Paint

  • Top-grade 100% acrylic. Satin on the body, semi-gloss on the trim.
  • Choose a sage with an LRV (light reflectance value) of about 45 or higher, because of the sun on the south and west walls.
  • Topcoat within the primer's recoat window (about 14–30 days). After that, wash, scuff and spot-prime first.
  • The porch wall is yellow now and may need two full coats, or a tinted primer, to cover evenly.

Washing (red dust)

  • Never power-wash this wall. With no sheathing or housewrap, water driven up under the laps goes straight into the insulation; high pressure also gouges the old wood, raises fibres and strips primer and lead paint.
  • Use a garden hose, or a pressure washer at 500 psi or less on a wide fan tip held well back. Scrub with a soft brush on a pole and a mild house wash.
  • Spray at the wall or downward, never upward into the laps. Keep the spray off the old sash and glazing putty, the electric meter and the gas regulator vent.
  • Stubborn red clay stains: oxalic-acid wood cleaner, tested on a small patch first.
  • Let the wall dry 1–2 days before painting.
  • When: a gentle wash of the primer right before the first sage coat, inside the primer window. After painting, once a year or when it looks red, mostly the bottom 2–3 ft.
  • Less dirt to begin with: the gravel strip, beds held 18–24" off the wall, soil sloped away and drip irrigation all cut down the clay that rain splashes onto the bottom courses. Satin paint sheds dust better than flat.

Cottage details

  • White trim throughout: wide casings, a frieze board, corner boards, and a white beam at the porch.
  • Shutters sized to half the window width. Window boxes on brackets that hold them about 1" off the wall.
  • Louvered gable vents. Tie the carport in with body-colour siding and square posts.
  • Planting beds 18–24" from the house, a gravel strip at the foundation, drip irrigation only.

Tools

Tool Choice Notes
Siding sander Festool Rotex RO 125, used about $300 on eBay (asked seller for a video and offered $280 shipped) Cheaper option: reconditioned Bosch GET75-6N at about $160
Finishing sander Festool ETS 125, used about $155 Good for trim, not for stripping
Dust Shop vac with HEPA cartridge and cyclone separator, about $60–120 A true HEPA extractor (DeWalt DWV010/012, Bosch VAC090AH) is better for lead
Stripping Infrared or heat stripper for thick paint Less lead dust than sanding
Joinery Festool Domino, planer Already owned

Interior walls (910)

Cover the existing paneling (cheap 4x8 sheets, some deterioration, unevenness mostly at the sheet seams) with 1/4" hardboard, then add vertical board and batten with crown, per the living-room rendering; replace window and door casings with new trim. All trim in primed finger-jointed pine (MDF dents and chips too easily). Main risks: moisture damage along the floor line, uneven seams telegraphing through, trim depth, heater clearances, and lead paint.

Living room before: painted 4x8 paneling, wall furnace, textured ceiling
Before. Painted 4x8 paneling, uneven at the seams.
Rendering of the living room with vertical board and batten, crown and new casings
Plan. Vertical board and batten, crown, new casings.
Room with wood-tone paneling swollen and split along the floor line
Fix first

Swelling along the floor line

  • Bottom edges are swollen and stained; one sheet is split.
  • Moisture-meter before covering. If dry, cut out the bottom band and let the tall baseboard cover it.
Bedroom with paneling partly primed, wallpaper border, original window casing
Decide

Top edge and trim depth

  • Choose: run battens to the ceiling (remove the border and trim) or stop at the trim line.
  • Stop priming the paneling; the Kilz goes on the hardboard.
  • Plaster sits behind the paneling here, so the doorway will need a jamb extension.

Prep and assessment

Layout

Demo

Hardboard

Windows and doors

Design and materials

  • Look: vertical battens only, floor to crown, about 16-24" on center so a batten lands on every 48" paneling seam
  • Optional single horizontal rail, undecided; decide before the verticals go up (adding later means cutting every batten in place). Options: frieze rail about 12" below crown, or aligned with the window stool (32-36"). Tape-test the height first
  • Battens: 3/4" thick x 2-1/2 to 3-1/2" wide (1x3/1x4) primed finger-jointed pine; hand-pick straight boards
  • Match thickness across all battens (some "1x" pine runs 11/16"); prime knots with shellac or oil primer
  • MDF only up high where nothing hits it (crown or frieze), if at all
  • Approx. cost per 8' 1x4: finger-jointed pine $12-16, primed MDF $8-12, poplar/clear pine $18-25

Board and batten

Safety

Kitchen (910)

The kitchen is mostly done: new base cabinets, counter, sink and gas range are in, and the plank floor is painted blue. What's left is finishing work and a few safety checks.

Done (May 2026)

  • Old base cabinets and blue sheet vinyl removed; the lower wall band behind the cabinets opened up.
  • Original open upper shelving kept and painted white, including the arch over the sink window.
  • New white shaker base cabinets, a marble-look laminate counter, a single-bowl drop-in sink and a gas range.
  • Plank floor primed white, then painted deep blue gloss.

Finish work

  • Floor: let the paint cure fully before sliding appliances on it (light traffic after about a week, full hardness takes up to a month). Felt pads under chairs. Don't sand the old boards; the paint under the new coat is presumably lead.
  • Add shoe moulding or quarter round where the floor meets the walls and cabinet toe kicks, then touch up the unpainted strips along the edges.
  • Caulk the counter-to-wall joint and add a backsplash. Beadboard or a simple tile suits the cottage look.
  • Close up and patch the lower wall band wherever it still shows.
  • Trim the pass-through to the living room and the back door to match the new casings in the interior walls plan.
  • Replace the fluorescent ceiling fixture with an LED fixture; consider lights under the upper shelves.

Safety checks

  • Every counter outlet GFCI-protected.
  • Gas range: anti-tip bracket installed, a shutoff valve you can reach behind it, and a new flexible connector. Put a CO alarm in or near the kitchen.
  • No range hood is visible in the photos. A vented hood is best with gas cooking; a recirculating one is the fallback.
  • If any old sheet vinyl or its backing is left, test it for asbestos before scraping.

Decide

  • Metal louvered window over the sink: replace with a wood double-hung to match the house, or add an interior storm panel.
  • Back door: keep the old glass-panel door (weatherstrip it and fix the threshold) or replace it.
  • Wall colour to go with the blue floor and white shelves.

Next steps

Sources

Well plan

Drill one shallow sand well, about 40–50 ft, on the empty lot between 922 and 910. Use it for irrigation first and keep city water in both houses for now. The pipe, pump and tank are sized so both houses can switch to well water later.

Nearby well records (OWRB)

Well Distance Depth Water at Material Yield
Latta #13625 ~0.5 mi S 45 ft 18 ft Sand at 18–27 ft over shale 12 gpm
Burton #13626 ~1.0 mi SSW 40 ft 15 ft Sand from 3–40 ft 15 gpm
Benedict #208531 ~1.2 mi NE 55 ft 21 ft Sand, coarse at 45–55 ft 45 gpm
James #176570 ~1.5 mi NE 45 ft 22 ft Wet sand at 20–32 ft over clay 10 gpm
City of Waurika #26433 ~1.9 mi NW 52 ft 12 ft Not logged (1954) 79 gpm
Hunter #92334 ~2.0 mi E 105 ft 20 ft Water sands at 22–35 and 80–105 ft 25 gpm

Deeper wells farther out went into red clay and made 1.5–8 gpm. None of the records include water quality.

Water quality

  • The main risk in the deeper red beds is salt and gypsum. For shallow sand wells in town, the risk is nitrate and bacteria.
  • Check each water layer with a TDS meter (about $20) as it comes in. Stop above any salty layer.
  • After drilling, send a sample to the OSU Soil, Water and Forage lab for the irrigation test (through the Waurika extension office). Add nitrate, bacteria and arsenic tests before anyone drinks it.
OSU turf rating Total salts (mg/L) SAR (sodium)
Good 320–960 1–2
Fair (manageable) 960–1,920 2–4
Poor 1,920–3,200 4–8
Unacceptable over 3,840 over 15

Build spec for the driller

  • Stop at the shale or red clay, probably 35–50 ft. Screen the whole water sand, with a gravel pack.
  • Grout seal of at least 10 ft, down to just above the water sand. Run a yield test and file the well log with OWRB.
  • Pitless adapter and 1" drop pipe. Pump matched to the tested yield (probably 10–12 gpm, likely ½ hp at this depth), with one pressure tank and pressure switch at the well serving both houses and the irrigation line. Details under Water line sizing.

M&M Water Well Service estimate (April 17, 2026, now expired)

Item Estimate (100 ft) At about 45 ft
Drilling at $45/ft $4,500 about $2,025
Pump, tank and fittings $3,000 $3,000
Total without well house $7,500 about $5,025
Well house option +$3,000 skip it; use the pitless setup

A dry hole is $20/ft. The $500 travel fee applies only over 50 miles.

Water line sizing (for house use later)

Sized for both houses on well water: 922 has 2 baths, 910 has 1. Usually 1–3 people in total, family gatherings of about 5, and a weekend of about 10 people once a year.

  • Daily use is about 70 gal per person: 70–210 gal on a normal day, about 350 at a gathering, about 700 on the 10-person weekend. A 10–15 gpm well makes 600–900 gal an hour, so the pipe only has to handle peak flow.
  • Design peak is 12–15 gpm: two showers plus a toilet or the washer. The pressure tank covers short bursts above the pump rate.
  • The goal is under 5 psi lost between the tank and each house.
LineLengthSizePressure loss
Well to 910 and to 922up to 100 ft1¼" HDPEabout 1.3 psi at 15 gpm (2.3 at 20)
Well to irrigation manifoldunder 200 ft1¼" HDPE, backflow preventerabout 1.3–1.8 psi at 10–12 gpm
Irrigation zones—1" PVC, ¾" at branch ends8–10 gpm per zone, one at a time
Inside 910 (1 bath) and 922 (2 baths)—¾" main line, ½" to fixtures—

For comparison, 1" HDPE loses about 5 psi per 100 ft at 15 gpm and runs faster than it should, so it is too small for the house lines. 1½" isn't needed at these lengths.

  • At the well: pump, then the pressure tank and switch, then a manifold with three branches (910, 922, irrigation), each with its own shutoff. A tank of about 44 gal is enough; an 86 gal tank makes the pump turn on and off less often. Put it in an insulated box with a little heat, not a full well house. A variable-speed pump isn't worth it at this level of use.
  • At each house: the 1¼" main runs to the house, with a shutoff and hose bib there, then steps down to ¾" inside.
  • Backflow: put a backflow preventer on the irrigation branch (double check valve or pressure vacuum breaker; ask the city which) so lawn water can't siphon back into drinking water.
  • City water: well water must never connect to the city system. Either disconnect from city water or install the backflow device the city requires.
  • Pipe: HDPE rated NSF-61 for drinking water, 200 psi, with tracer wire. Bury it 18–24" deep, about 10 ft from sewer lines, or cross them with about 18" of vertical separation (confirm with the city).
  • Operating rules: water the lawn at night; turn irrigation off on big-gathering weekends (the water heater runs out before the well does).
  • Before anyone drinks it: test for nitrate, bacteria, arsenic and fluoride, in addition to the irrigation test.

Layout and pipe

  • Well on the empty lot: in the open, clear of trees and power lines, away from sewer lines, with truck access from Anderson.
  • Mains to each lot: 1¼" HDPE rated for drinking water, buried at least 18", with the pump cable in conduit. See Water line sizing above.
  • Zones: 1" PVC, with ¾" at branch ends. Size each zone at 8–10 gpm and run one at a time.
  • About 12 gpm covers roughly 1" a week on 20,000 sq ft of lawn, at around 17 hours of pumping a week.
  • Power from the nearer house. Record an easement, or combine parcels, before any lot is sold.
  • Grass: zoysia in the yards, Bermuda seed on the lot. See Lawn below. Both are dormant from about November to March.

Lawn

Three grass zones across the two yards and the lot: zoysia at the houses for a thick, uniform lawn, and Bermuda on the empty lot for fast, cheap green. Soil work happens this fall; planting is late May to July 2027, once the well and irrigation are running.

Zones

AreaGrassWhy
910 front yardZoysia sod (Meyer or Palisades)Thick right away where it shows most
910 back yard and under the treesZoysia seed (e.g. Zenith), or plugs cut from the same sodCheaper; fills in over about 2 seasons; handles partial shade
922 yardsZoysia (front: sod or seed to decide; back: seed)Same grass at both houses
Empty lot (well site)Bermuda seed, hulled (common, or Riviera or Yukon for better colour)Green and fast: thick in one summer, cheapest, takes wear and salt best
  • Border between the Bermuda lot and the zoysia yards: steel edging 5–6" deep, or a 1–2 ft gravel or mulch strip, on each side where the lot meets a yard. Pull any Bermuda runners that cross it once or twice a season. Without it, Bermuda spreads into the zoysia and the yards turn patchy.
  • Skip the winter rye overseed on the zoysia; it doesn't take it well.

Before digging

  • Call OKIE811 at least two working days ahead. Gas service lines, sewer laterals and electric run to both houses.
  • OSU soil test through the Jefferson County extension office: pH, phosphorus, potassium, organic matter, and sodium and salts. Don't add lime or sulfur without it.
  • Trench the well mains and irrigation zones before final grading, so a new lawn doesn't get dug up.

Soil prep on the red clay (this fall)

  • Work the clay only when it's moist, not wet. A handful should crumble when squeezed, not smear into a ribbon.
  • Yards (zoysia): rotary plow 6–8" deep, spread 1–2" of compost (deepest where the sod goes), and till it into the top 4–6". Stop while it's still crumbly, before it turns to powder.
  • Lot (Bermuda): rotary plow 4–6", one tiller pass, and little or no compost (½" only on the worst bare or packed spots). Fertilize per the soil test.
  • Compost: about 3 cu yd per inch per 1,000 sq ft. Buy screened, finished compost; if it's manure-based, ask about salt and weed seed.
  • Gypsum only if the soil test shows high sodium. No sand; a little sand in clay makes it harder.
  • Grade so the soil falls about 6" over the first 10 ft from each house, and keep at least 6" of foundation showing. Don't build amended soil up against the walls.
  • Rake out rocks and roots, then roll lightly with a water-filled roller.
  • Keep the trees healthy: don't plow inside the drip line of the big trees. Go shallow there, or just top-dress.
  • Over the winter: sow cereal rye as a cover crop to hold the soil and keep red mud off the siding. Mow and till it in by about April, at least 3 weeks before planting.

Planting (late May to July 2027)

  • Soil at 65°F or warmer, after the well is drilled and the zones work.
  • Zoysia sod: water daily for 2–3 weeks until it roots, then deep watering 2–3 times a week. Mow at about 1½–2".
  • Zoysia seed or plugs: keep seed moist (several light waterings a day) for 3–4 weeks. Plugs: 2" pieces cut from sod on 12" centres; 1 sq ft of sod makes about 36 plugs.
  • Bermuda seed on the lot: about 1–2 lb per 1,000 sq ft, raked in ¼" or less and rolled. Keep it moist for 2–3 weeks. For fast fill, about 1 lb of nitrogen per 1,000 sq ft at about 4 weeks, then monthly through August. Mow at 1–1½" once it's about 2" tall.

Rough costs

Per 1,000 sq ft, materials only, rough ranges, not quotes. Call sod farms near Waurika.

ItemCost
Zoysia sodabout $450–900 (installed: add about $1–1.50 per sq ft)
Zoysia seedabout $25–60
Zoysia plugs cut from sodabout $15–30
Bermuda seedabout $10–30
Compost, 1"about 3 cu yd, very roughly $30–50 a yard plus delivery

Lawn areas aren't measured yet. Once they are, this becomes a pallet count and a compost order.

If the water or soil is salty

  • Bermuda is the most salt-tolerant of these grasses; fine-leaf zoysia (Zeon) is close behind; Meyer and Palisades are moderate.
  • If the well water tests over about 1,500 µS/cm (the OSU "Fair" range or worse), or the soil test shows salt or sodium, switch the sunny yard areas to Bermuda or Zeon, flush with an occasional deep watering, and add gypsum if sodium is high.
  • Buy the zoysia only after both tests are back.